首页 > 新闻动态 > 其他 > Coin Counter's User's Guide
产品目录
中国 产品目录 制造商
最新消息

OCOM 通过“国家高新技术企业”认证

2023年11月7日,根据全国高新技术企业认定管理工作领导小组办公室的公告,深圳市澳凯码科技有限公司顺利通过了“国家高新技术企业”认定,由此正式迈入国家高新技术企业行列。

OCOM 阿里巴巴“超级2023年9月”金融设备供应商第一名

OCOM 阿里巴巴“超级2023年9月”金融设备供应商第一名

祝贺OCOM喜获“软件著作权”和六项“实用新型专利”证书

时值公司成立15周年庆典之际,OCOM喜事不断,近日公司再获三项“软件著作权”和六项“实用新型专利”证书。

OCOM 十五周年庆典隆重举行

2022年7月2日,OCOM十五周年庆典在深圳市南山区亚朵S酒店隆重举行。
认证
联系我们
地址:深圳市南山区南山大道南油第四工业区2栋4层3A01,518054
电子邮件:ocom@ocominc.com,info@possolution.com.cn; 
联系电话:+86.755.86053207,分机800; 
传真:+86.755.86053207分机868;
QQ:2485890637; 
微信/WHATSAPP/Viber:0086-13352932860. 现在联系

消息

Coin Counter's User's Guide

Lily Li Originality 2016-05-20 17:19:28

USER’S GUIDE

      FOR ELECTRONIC COIN SORTER

WARNING!

For your safety, it is very important that you always follow the simple

Precautions as below:

- Do not operate the machine if you, or it, are damp. Operating the machine

under wet damp conditions can lead to an electrical shock hazard that

might result in serious injury.

 

-Use only the same type and rating when replacing a fuse. Using an incorrect Fuse can cause a potential fire hazard if a higher rating Fuse is used.

 

-Ensure that both the machine and the domestic mains supply system are of the same voltage. An in correct supply voltage could cause a potential fire hazard.

 

-Turn off and unplug the power before performing maintenance.

 

-Do not start the machine when the back cover is open.

 

-Do not put your fingers inside the hopper or channel when the machine is under operation.

 

-Turn off and unplug the power when long time no using.

 

-Should you have any doubts, please contact your local distributor, or sales agent, for further advice.

 

 

                   Coin Drawer  Fuse(at the bottom)

SPECIFICATION

Ambient temperature

0~40 degC

Ambient Humidity

30~80%

Hopper capacity

Max.500units

Each coins drawer

50~300units

Batch preset number display

3 Digits LED

Counting number display

4 Digits LED

Power source

AC220V/50HZ□

AC110V/60HZ□

Power consumption

<45W

Dimensions

345x306x260(mm)

Net weight

3.9kg

Counting speed

Max.270units/min

**In the interest of our ongoing policy of continual improvement,

specifications are subject to change without prior notice.  ***

OPERATION

1.Make sure that the machine is put on level and then turn on the machine.

2.Set an expected batch.

  Each channel can be set an expected batch (from 0 to 999).

Press the “SET” key to select the channel, and the “BAT” key, “+” key and “-” key to set the expected batch number.

Note 1: If some channels set the batch to 0, the machine will not stop this channel even the drawer is full, unless the “START/STOP” key is pressed or no coin drop though the channel within 20 seconds.

Note 2: Keep “-” key pressed in 7 seconds can set all the channels to

batch 0.

Note 3:The batch setting can be automatically memorized.

3.Start counting

Put coins in the hopper,and press the “START/STOP”key to start counting.

Press the “START/STOP” again to stop the counting.

4.Check the report

  Press the “REPORT” key circularly when the machine in standby state can check the counting results of each channel. Press the “C” key can exit this checking procedure.

MAINTENANCE WARNING!

TURN OFF THE MACHINE AND UNPLUG THE POWER BEFORR THE FOLLOWING MAITANENANCE!

1.Foreign object falls into the hopper will cause jamming or even damage the machine! Please do avoid the foreign object falls in.

As following shown, to remove the foreign object, just open the back Cover and pick out the foreign object.


2.To remove the coin jamming, as following pictures shown, use a finger to push up the jammed coin and let it fall out from the gap between the channels.

3.If the machine is switched on, the electron undergoes a test itself. It may results in one of the following error messages:

EA: Means optical sensor blocked: stop the machine and remove the back cover, then turn the carry tray by your hands, by outer light you see the glass which on top left corner, then clear the dust on the glass. Because there is too much dust on the glass and it affects the optical sensor work. 

If the machine often appears EA, it may be due to working environment leading too much dust in the inner of the machine, to clean the inner parts of the machine. a: switch off the machine and cut down power. b: remove 3 bolts on bottom of crust, remove the crust. c: clean dust, end to reset.

E1…E8 Means count sensor blocked.(According to the coin diameter from short to long range)

E9 Means running sensor blocked.

If it takes no effect after cleaning the inner parts as well as sensors, the machine needs repaired.